CVE-2026-66013OpenRemote before 1.26.2 contains an authentication bypass vulnerability in the console registration API that allows unauthenticated attackers to update existing console assets by supplying a known asset identifier. Attackers can overwrite push notification tokens and console metadata without authentication or ownership validation, redirecting notifications or denying delivery to legitimate consoles.
2026-07-25 · score —
CVE-2026-64529In the Linux kernel, the following vulnerability has been resolved:
crypto: qat - remove unused character device and IOCTLs
The QAT driver exposes a character device (qat_adf_ctl) with IOCTLs
for device configuration, start, stop, status query and enumeration.
These IOCTLs are not part of any public uAPI header and have no known
in-tree or out-of-tree users. Device lifecycle is already managed via
sysfs.
The ioctl interface also increases the attack surface and is the
subject of a number of bug reports.
Remove the character device, the IOCTL definitions, and the related
data structures (adf_dev_status_info, adf_user_cfg_key_val,
adf_user_cfg_section, adf_user_cfg_ctl_data). Drop the now-unused
adf_cfg_user.h header and strip adf_ctl_drv.c down to the minimal
module_init/module_exit hooks for workqueue, AER, and crypto/compression
algorithm registration.
Clean up leftover dead code that was only reachable from the removed
IOCTL paths: adf_cfg_del_all(), adf_devmgr_verify_id(),
adf_devmgr_get_num_dev(), adf_devmgr_get_dev_by_id(),
adf_get_vf_real_id() and the unused ADF_CFG macros.
Additionally, drop the entry associated to QAT IOCTLs in
ioctl-number.rst.
2026-07-25 · score —
CVE-2026-64528In the Linux kernel, the following vulnerability has been resolved:
tty: serial: samsung: Remove redundant port lock acquisition in rx helpers
Sashiko identified a deadlock when the console flow is engaged [1].
When console flow control is enabled (UPF_CONS_FLOW),
s3c24xx_serial_stop_tx() calls s3c24xx_serial_rx_enable() and
s3c24xx_serial_start_tx() calls s3c24xx_serial_rx_disable().
The serial core framework invokes the .stop_tx() and .start_tx()
callbacks with the port->lock spinlock already held. Furthermore, all
internal driver paths that invoke stop_tx (such as the DMA TX
completion handler s3c24xx_serial_tx_dma_complete() or the PIO TX IRQ
handler s3c24xx_serial_tx_irq()) also acquire port->lock prior to
calling it. (Note that s3c24xx_serial_start_tx() is only invoked by the
serial core).
However, s3c24xx_serial_rx_enable() and s3c24xx_serial_rx_disable()
unconditionally attempt to acquire port->lock again using
uart_port_lock_irqsave(). Since spinlocks are not recursive, this
causes a deadlock on the same CPU when console flow control is engaged.
Remove the redundant lock acquisition from both rx helper functions.
2026-07-25 · score —
CVE-2026-64527In the Linux kernel, the following vulnerability has been resolved:
drm/hyperv: validate VMBus packet size in receive callback
hyperv_receive_sub() reads msg->vid_hdr.type and dispatches into one
of four message-type branches without knowing how many bytes the host
wrote into hv->recv_buf. The completion path then runs
memcpy(hv->init_buf, msg, VMBUS_MAX_PACKET_SIZE), so the consumer that
wakes on wait_for_completion_timeout() can read up to 16 KiB of
residue from a prior message as if it were the response payload.
Pass bytes_recvd into hyperv_receive_sub() and reject any packet that
does not cover the pipe + synthvid header. A single switch on
msg->vid_hdr.type then computes the type-specific payload size: the
three completion-driving types (SYNTHVID_VERSION_RESPONSE,
SYNTHVID_RESOLUTION_RESPONSE, SYNTHVID_VRAM_LOCATION_ACK) fall through
to a shared exit that requires that size before memcpy/complete, while
SYNTHVID_FEATURE_CHANGE validates its own payload and returns before
reading is_dirt_needed. Unknown types are dropped.
SYNTHVID_RESOLUTION_RESPONSE is variable length: the host fills
resolution_count entries, not the full SYNTHVID_MAX_RESOLUTION_COUNT
array. Validate the fixed prefix first so resolution_count can be
read, bound it against the array, then require only the count-sized
array, so the shorter responses the host actually sends are accepted.
Only run the sub-handler when vmbus_recvpacket() returned success. The
memcpy length is bytes_recvd, which is bounded by VMBUS_MAX_PACKET_SIZE
only on a successful receive; on -ENOBUFS vmbus_recvpacket() instead
reports the required length, which can exceed hv->recv_buf, so copying
bytes_recvd would read and write past the 16 KiB buffers. Gating on the
success return keeps the copy bounded. The nonzero-return path is itself
a malformed-message case and is now logged rather than silently skipped;
channel recovery is not attempted.
Rejected packets are reported via drm_err_ratelimited() rather than
silently dropped, matching the CoCo-hardened pattern in
hv_kvp_onchannelcallback().
2026-07-25 · score —
CVE-2026-64525In the Linux kernel, the following vulnerability has been resolved:
xfrm: move policy_bydst RCU sync from per-netns .exit to .pre_exit
The struct pernet_operations docstring in include/net/net_namespace.h
explicitly warns against blocking RCU primitives in .exit handlers:
Exit methods using blocking RCU primitives, such as
synchronize_rcu(), should be implemented via exit_batch.
[...]
Please, avoid synchronize_rcu() at all, where it's possible.
Note that a combination of pre_exit() and exit() can
be used, since a synchronize_rcu() is guaranteed between
the calls.
xfrm_policy_fini() violates this: it calls synchronize_rcu() before
freeing the policy_bydst hash tables (so no RCU reader is mid-
traversal at free time), but runs from xfrm_net_ops.exit -- once per
namespace -- so a cleanup_net() of N namespaces pays N full RCU
grace periods serially.
Use the documented pre_exit/exit split. Move the policy flush (and
the workqueue drains it depends on) into a new .pre_exit handler;
xfrm_policy_fini() then runs in .exit and frees the hash tables
after the synchronize_rcu_expedited() that cleanup_net() guarantees
between the two phases. Providing O(1) RCU grace periods per batch
instead of O(N).
Observed on Linux 6.18 with a workload doing unshare(CLONE_NEWNET)
at ~13/sec sustained: cleanup_net() and the netns_wq rescuer kthread
both stuck in xfrm_policy_fini()'s synchronize_rcu(), >300k struct
net accumulated in the cleanup queue, Percpu in /proc/meminfo climbed
to 130+ GB on 256-CPU hosts, and memcg OOMs followed. setup_net and
__put_net counts were balanced, ruling out a refcount leak.
2026-07-25 · score —
